Home
Hardware
Configurator
Services
OEM Guides About us Warranty Contact
ESENDEFRITPT
Manufacturers · Vehicles and mobile machinery

Computer for vehicles and mobile machinery: power, vibration and ignition start

A computer on board a vehicle lives off the battery, switches on and off with the key and spends the day vibrating. This guide explains what to ask of it so the disk does not get corrupted, it never runs out of power and it is still the same machine five years on.

ACD&CO technical team7 November 20267 min read

Power: 12 or 24 V from the vehicle battery

A vehicle battery does not deliver clean voltage: it drops when the engine starts, rises with the alternator and receives transients from other equipment. The computer must accept a wide DC range (9 to 36 V covers 12 and 24 V vehicles) and protect itself against those transients, which the ISO 7637 standard describes for automotive use.

Ask also for battery protection: the unit should shut itself down when voltage drops below a threshold, so it never leaves the vehicle unable to start in the morning.

Start and shutdown with the key, with a delay

The unit must switch on with the ignition and, when the key is removed, shut the system down cleanly after a configurable delay (seconds to minutes) to save data and close applications. That ignition input and that delay come with the power supply of vehicle computers; an office PC with an adapter has neither, and every abrupt power cut is a chance to corrupt the disk.

Vibration, shock and temperature

No moving parts: SSD, fanless if the power draw allows it, locking connectors (M12 or screw-lock) and the unit mounted on anti-vibration mounts. The vibration and shock tests of MIL-STD-810H are the reference we use in our industrial range. For temperature, ask for the range your vehicle needs (a cab in the sun is not a boot) and require that it has been tested.

Ask for the unit to be tested with its final power source, simulating engine starts and ignition cuts. That is where machines that worked fine on the bench fail.

Connectivity: 4G or 5G, GNSS, Wi-Fi and vehicle buses

The usual set is a 4G or 5G modem with a SIM slot, a GNSS receiver (GPS, Galileo) for position and time, Wi-Fi to offload data at base and, depending on the vehicle, CAN bus to read the machine state or RS-485 for sensors. Count the antennas and where they go: a unit inside a metal enclosure needs external connectors.

Cameras, recording and on-board vision

If the vehicle carries cameras (assistance, inspection, recording), decide how many and with which interface: GigE cameras with PoE or USB3. Recording several cameras continuously needs an SSD with capacity and write endurance; analysing them with an AI model needs a GPU, which in a vehicle should be low-power and cooled without dust.

Indicative starting points

Starting points for the computer in a vehicle or mobile machine
CaseForm factorStarting point
Data logging and telemetryFanless compact unit, 9 to 36 VLow-power processor, 8 to 16 GB, industrial SSD, 4G and GNSS
Operator terminal in the cabTouch panel PC with vehicle power inputThe same, with a sunlight-readable screen and ignition start
Mobile robot or indoor autonomous vehicle (AGV, AMR)Compact unit with a GPULow-power 16 GB GPU, 32 GB of memory, PoE ports and CAN bus
Recording and inspection with several camerasCompact unit with a GPU and two SSDs16 to 24 GB GPU, recording SSD separate from the system, 5G

Frequently asked questions

Will a normal mini PC with a 12 V converter do?

It works until the first cold engine start or the first abrupt shutdown. A vehicle computer accepts 9 to 36 V, withstands transients, switches on with the ignition and shuts down with a delay. That is the difference between a healthy disk and a corrupted one.

How does the unit shut down when I remove the key?

The power supply reads the ignition signal and, when it is lost, starts a clean system shutdown after a configurable delay. Data is saved and applications are closed before power is cut.

Do I need fans?

If the power draw allows it, no: a fanless unit draws in no dust and has no parts that wear out with vibration. With a GPU for artificial intelligence, filtered cooling or a low-power GPU is used.

Can you integrate the modem and the antennas?

Yes. We fit the 4G or 5G modem, the GNSS receiver and the Wi-Fi with their external antenna connectors, and test the unit with its final power source before shipping it.

Tell us about your product

Tell us what it does, where it will work and how many units a year. We will propose the machine, the lead time and the price in writing within 12 working hours.

Ask for a proposal

A proposal within 12 working hours

Tell us what you need

Tell us what it is for and we will reply with a configuration and its price. If you already have a quote from another brand, send it over and we will prepare the equivalent.

  • A written reply within 12 working hours
  • A single point of contact, from quote to warranty
  • No obligation: we only use your details to reply

+34 613 17 68 06info@acdcompany.es

This field is required.
Check the email: something is missing.

Or call us: +34 613 17 68 06