Home
Hardware
Configurator
Services
OEM Guides About us Warranty Contact
ESENDEFRITPT
Manufacturers · Regulation · CE

CE marking a product with a computer inside: what applies and what to ask the supplier for

The computer you buy carries a CE mark. Your product, with that computer inside, needs its own. It is not inherited: you sign it, as the manufacturer. This guide sums up which rules usually apply, what changes when the machine goes inside your enclosure and which papers its builder must give you.

ACD&CO technical team10 November 20267 min read

The CE mark on the parts is not the CE mark of the product

Each CE-marked component complies on its own. When they are joined in a new product, with another enclosure, other cabling and another power supply, the whole behaves differently: it emits differently and withstands differently.

That is why the manufacturer of the final product carries out its own assessment and signs its own EU declaration of conformity. The CE mark on the computer is a good starting point, not the end.

This guide is for information and sums up the rules as of November 2026. It does not replace a laboratory or a CE marking specialist for your specific product.

Which rules usually apply

Usual European rules for a product with a computer inside
RuleWhen it applies
Electromagnetic compatibility, Directive 2014/30/EUWhenever there are electronics: what the product emits and what it withstands
Low voltage, Directive 2014/35/EUIf it is powered at between 50 and 1,000 V AC or between 75 and 1,500 V DC
Radio equipment, Directive 2014/53/EUIf it has Wi-Fi, Bluetooth or a modem; it then also covers safety and compatibility
Hazardous substances (RoHS), Directive 2011/65/EUIn almost all electrical or electronic equipment, with few exclusions
Machinery, Directive 2006/42/EC and Regulation (EU) 2023/1230If the product is a machine; the regulation applies from 20 January 2027
Cyber resilience, Regulation (EU) 2024/2847Products with digital elements; full obligations from 11 December 2027

Which rules concern your product depends on what it is and where it is used. That decision is yours, and it is best taken at the start of the design.

What changes when the computer goes inside your enclosure

Three things are looked at again. Emissions and immunity: a well-closed metal box helps; a plastic one, a window or a long unfiltered cable does not. Electrical safety: the power supply, the clearances and the earthing inside your product. And heat: the computer was tested in its own chassis, with its own cooling, and inside yours the air flows differently.

The usual harmonised standards for computing equipment are EN 55032 for emissions, EN 55035 for immunity and EN IEC 62368-1 for safety. In industrial environments, EN IEC 61000-6-2 and EN IEC 61000-6-4 are used as well.

Which documents to ask the computer’s builder for

  • The EU declaration of conformity of the machine and of its main components: power supply, board and radio modules.
  • The electromagnetic compatibility and safety test reports, if they exist for that configuration.
  • The bill of materials, with manufacturer and part number of each part, and the commitment to give notice before changing any.
  • The RoHS and REACH declarations of the components.
  • The power supply data: safety certificate, power and efficiency.
  • The firmware versions and the software list, for your cyber resilience documentation.

Keep it all in your technical documentation. The directives require it to be kept for ten years from the moment the product is placed on the market.

Why it matters that the platform does not change

A test is valid for the configuration tested. If the supplier changes the power supply, the board or the Wi-Fi module without notice, your documentation no longer describes what you sell.

With a frozen platform, every change is notified beforehand and you decide whether any test has to be repeated. It is one of the four commitments of our OEM programme.

The case of Wi-Fi and the modem

Adding radio changes the directive. Using an already certified module saves a lot of testing, but not all of it: the conditions of its certificate, such as the antenna, must be respected, and the whole must be checked.

Since 1 August 2025, radio equipment that connects to the internet must also meet cybersecurity requirements.

Frequently asked questions

If the computer has a CE mark, does my product already have it?

No. The CE mark on the computer covers the computer. Your product is another device, with another enclosure and another use, and it needs its own assessment and its own declaration of conformity.

Do I have to go through a laboratory?

For most electronic products, the rules allow the manufacturer to assess conformity itself. In practice, emission and immunity tests are done in a laboratory, because they need facilities that almost nobody has.

Who signs the declaration of conformity?

The manufacturer of the final product: whoever places it on the market under its name. If you sell under your brand a machine that someone else builds, you sign, supported by the documentation they hand over.

What happens if I change a part of the computer?

It depends on the part. A different power supply, board or radio module can change the test results. That is why a frozen platform is advisable, with prior notice of every change.

Tell us about your product

Tell us what it does, where it will work and how many units a year. We will propose the machine, the lead time and the price in writing within 12 working hours.

Ask for a proposal

A proposal within 12 working hours

Tell us what you need

Tell us what it is for and we will reply with a configuration and its price. If you already have a quote from another brand, send it over and we will prepare the equivalent.

  • A written reply within 12 working hours
  • A single point of contact, from quote to warranty
  • No obligation: we only use your details to reply

+34 613 17 68 06info@acdcompany.es

This field is required.
Check the email: something is missing.

Or call us: +34 613 17 68 06